Updated on Reading Time: 3 minutes
Is your Mercedes-Benz engine’s squealing sound, A/C, and power steering not working correctly? Learn how to fix the problem by replacing the serpentine belt of your Mercedes-Benz.
Repair Time:
The typical time range in hours required to complete this repair.
Repair Cost:
The average repair cost range in USD to complete this repair by either an honest mechanic or as a DIY. Including the cost of parts but not tools.
Repair Difficulty:
This indicates how difficult it is for most DIYers and mechanics to perform this repair.
This guide provides instructions on changing the serpentine belt on most diesel Mercedes-Benz vehicles, including E-Class, C-Class, CLK-Class, ML, GL, R-Class, and Sprinter equipped with the 3.0 diesel engine, OM642. Generally applicable to models that end with 320 CDI or 350 BlueTec. Replacing the serpentine belt on a Mercedes Benz 3.0L diesel engine is relativity easy and takes aboutan hour.
Symptoms
Common symptoms indicating a problem with your Mercedes Benz serpentine belt include:
YOUCANIC Pro Manuals
Give you access to the original OEM Factory Repair Manuals. Each manual offers meticulously detailed steps and vivid illustrations, extensive wiring diagrams, precise torque specifications, and exclusive access to technical service bulletins and OEM service information—everything you need, just what the dealerships use.
Learn More
- Whistling or squealing sound in the front end of the engine.
- Wear and cracks in the belt.
- Components like AC and power steering are not working correctly.
What you will need
Parts
- Mercedes-BenzSerpentine BeltOM642
Tools
- E-10 Torx socket
- 17mm socket
- 8mm combination wrench
- Flat screwdriver
Procedure
Follow these steps to change the serpentine belton a Mercedes Benz 3.0L engine.
Removal
- Park the vehicle on level ground and let it cool down. If the engine is still hot, you risk getting burned.
- Pull the hood release under the dashboard and open the hood. Secure the hood with the hood support.
- Remember to disconnect the battery’s negative terminal every time you work with your serpentine belt to prevent accidents or damage to you and some of the vehicle components you are working with.
- To disconnect the lower intercooler hose, use a flat screwdriver, slide the metal clip off, and then push it down and separate it from the upper hose. Once the hose is disconnected, you can remove the Torx bolts of the noise-damping hose using an E-10 Torx socket, but if it is not available, you can also use an 8mm combination wrench or 8mm socket. After removing the two bolts, one metal plate still holds the hose. Remove the screw, remove the metal plate, and pull the hose out.
- Before removing the serpentine belt, take a clear photo or draw the belt’s routing pattern to the pullies; this will serve as a reference when installing the new serpentine belt.
- Removing the serpentine belt requires you to access the belt tensioner; remember, you do not have to remove the bolts of the tensioner because you are just replacing the belt. You need to use a 17mm socket and place it on the tensioner’s service bolt, push the handle down counterclockwise, and slide the belt off. You can now separate the belt from all the pullies it serves.
Installation
- Using the photo or drawing of the belt’s routing pattern you made earlier as a reference, start placing the belt on the pullies. Ensure that the belt is seated correctly on each pulley because if not, the length of the belt may become a little bit short. It will not give you enough length when you try and place it on the tensioner. Place your 17mm socket to the service bolt, push the handle counterclockwise, and slide the belt in. Slide your fingers to each pulley to double-check if the belt is seated correctly.
- Clean and install the noise-damping hose, place the metal plate properly, tighten the screw, install the upper and lower bolts, and tighten it to its specified torque.
- Reconnect the lower intercooler hose and fix the metal clip to lock; push it down to ensure it is properly connected.
- Install thebattery if disconnected.
- Start the engine and verifythe fix.
How much does it cost to replace a Mercedes Benz serpentine belt?
- The average cost to replace a Mercedes Benz serpentine belt at a repair shop is between $100and 250. Labor costs are estimated between $80and $150, while parts are priced between $22 and $90.
How often do serpentine belts need to be replaced?
- On average, the Serpentine Belt is supposed to be replaced every 60,000-100,000 miles, but you should always follow your car’s service manual for the replacement intervals.
We hope you find the Mercedes-Benz Serpentine Belt Replacement 3.0 Diesel Engine guide helpful. Check these troubleshooting and repair guides for more help on your Mercedes-Benz.
Written and fact-checked by:
YOUCANIC Techs YOUCANIC articles are written by authors who collectively have over 60 years of experience in the automotive field and years of hands-on experience on vehicles. These authors are certified ASE G1 Automotive Maintenance engine professionals (the highest level certification for vehicle maintenance and repair). They hold associate’s and bachelor’s degrees, as well as having gone on to further study to receive a master’s and doctorate degrees. These authors collaborate on research, writing, editing, and fact-checking every article to ensure that it is accurate and up to date and delivers the best counsel and information to YOUCANIC readers. View all postsRush*t Hila is an engineer and ASE certified in G1 Automotive Maintenance 
